| 品牌:嘉宝莉 | 类型:其他 | 颜色:黑色 |
| 保质期(个月):12 |
LC-300 SOLID FILM LUBRICANT
HEAT CURING
SERIES V765 LEAD FREE
MEETS SAE SPEC AS5272C TYPE I (FORMERLY MIL-L-46010 TYPE I)
DESCRIPTION
Sandstrom LC-300 Dry Film Lubricant is a lead free lacquer-like
coating containing molybdenum disulfide and corrosion-inhibiting
pigments. This Heat Curing material prevents corrosion, galling,
seizing, and fretting. It is a low-friction coating which exhibits long
wear life when operated at -320oF to +400oF under loads exceeding
100,000 psi.
LC-300 should be applied in place of Sandstrom 9A where
maximum wear life and corrosion protection from a dry film lubricant
are required on metals which may be adversely affected by
9A&锛�39;s 1 hour @ 400oF bake cycle.
Once Sandstrom LC-300 has been heat cured, it is virtually
unaffected by atmospheric and fretting corrosion, solvents, acids,
oils, and degreasers, and is not resoftened again at elevated
temperatures.
LC-300 may be applied to a wide variety of surfaces by spraying or
dipping. Complete application instructions are on the reverse of
this sheet.
OUTSTANDING FEATURES/BENEFITS
Excellent Corrosion Protection, Chemical Resistance, and Long
Wear Life are its outstanding characteristics.
SANDSTROM LC-300 CONTAINS NO LEAD OR GRAPHITE
TYPICAL USES
Sandstrom LC-300 is an excellent solution to the problem of
lubricating parts:
鈥� Where "clean operation" is desired (LC-300 will not collect dirt and
debris as do grease and oils)
鈥� Where parts may be subjected to frequent disassembly
鈥� Where a protective coating and sacrificial break-in lubricant are
needed
鈥� Where fretting and galling is a problem (such as splines, universal
joints, and keyed bearings)
鈥� Where easy release is desired (such as acme nuts and screws
and PVC molds)
鈥� Where metallurgical properties are adversely affected by baking
at temperatures higher than 300oF
鈥� That will be operated in corrosive atmospheres
鈥� That may be stored for long periods
鈥� Which are seldom lubricated once they leave the factory and
where permanent lubrication is desired
鈥� Where operating pressures exceed the load-bearing capacities of
ordinary oils and greases
COMPOSITION AND PHYSICAL PROPERTIES
Net Weight per gallon 10.20 lbs + .2 lb
Solids content 41.0% + 1%(By Wt.)
Viscosity 80-95 sec / #1 Zahn
Flash point 43oF + 2oF Setaflash
Operating temperature
range -320oF to +400oF
Wear life 298 minutes average
ASTM D2625A
Load carrying capacity 2750 lbs. *
ASTM D2625B
Vehicle type Modified Vinyl
Lubricative pigment Molybdenum Disulfide
Color Flat Dark Gray
Shelf life 1 year from date of manufacture
Specifications SAE Spec AS5272C Type I
PRI QPL AS5272 type 1
Corrosion protection
Sulfurous Acid-Salt Spray 4 cycles with no effect *
Fed-STD-791c Method 5331.1
ASTM B117 1000 hours*
MIL-DTL-16232 type M or Z class3
TECHNICAL INFORMATION GUIDE
PORT BYRON, IL 61275 鈥� (309) 523-2121
1-800-747-1084 FAX # 1-309-523-3912
*Tests halted before failure
GENERAL
Sandstrom LC-300 is a paint-like material consisting of lubricative
pigments dispersed in a thermosetting resin system thinned with appropriate
solvents. For maximum service, the APPLICATION INSTRUCTIONS
MUST BE FOLLOWED CLOSELY. The lubricant is flammable and the safety
precautions usually followed when using flammable materials should be
observed.
FILM THICKNESS AND ENGINEERING TOLERANCES
As supplied, Sandstrom LC-300 will yield a film thickness of about .0005
inches per dip coat. Usually engineering tolerances will permit necessary
minimum film buildup of .0002 to .0003 inches without interference. If
excess buildup does occur and a force fit is necessary, burnishing lightly
will assist in mating the parts. The remaining excess will be worn away in
the first few cycles of operation. Whenever possible, the proper tolerances
比尔安达(上海) 润滑材料有限公司是中国拥有WS2系列固体润滑技术的高科技企业,可为汽车行业,模具,医疗设备,食品机械,纺织业等各种机械活动部件表面进行WS2固体(干膜)润滑处理。我公司的大型射频磁控溅射真空WS2镀膜机,可以大批量为汽车行业,军事工业的客户进行WS2表面处理加工服务。作为美国芝加哥Micro Surface公司公司WS2技术在大中国地区的代理,我公司将努力***中国市场。 公司成立以来,已向中国国家***局提交了《采用物***相沉积法制备二硫化钨固体润滑膜的方法》等7项发明***申请。我公司的物***相沉积中的射频磁控溅射法制造WS2固体润滑复合膜工业化生产工艺,填补了我国该领域的空白,该项目产品综合技术达到国际***水平。 目前我公司在美国芝加哥和上海宝山城市工业园区建有科研和生产基地,技术力量雄厚。公司拥有国际***的实验设备和严格的质量检测系统,使得产品从研制、原料采购、生产制作等一系列过程都处在严密的控制下,***了产品质量。公司主要对企业所提供的部件进行WS2表面处理,可及时、有效地为客户提供优质服务。 同时,我公司负责在中国磁铁行业推广和销售美国Everlube公司1221等磁铁专用涂层.我们也能为客户的产品进行二硫化钼,铁氟龙,Everlube 620C/6102G/5396/1221/1201/1301,TiN(氮化钛),DLC(类金刚石)等各种涂层加工。
点击查看>| 企业类型 | 外资企业 | 注册资本 | 11.00万美元 | ||
| 公司注册地址 | 上海市宝山区长建路198号 | 统一社会信用代码 | 913100007616437727 | ||
| 法定代表人 | 郁水峰 | 公司成立日期 | 2004-05-08 | ||
| 营业期限 | 111111 | 经营范围 | 镍铁富龙涂层,ni-p-PTFE,ws2固体润滑,everlube620c涂层,表面处理,金属表面处理,干膜润滑,ws2 | ||

