| 产品特性:多级泵 | 品牌:凯泉 | 型号:DG85-45*9 |
| 材质:铸钢 | 性能:变频 | 用途:管道泵 |
| 扬程:150m | 驱动方式:电动 | 输送介质:清水泵 |
| 泵轴位置:卧式 | 叶轮结构:敞开式叶轮 | 叶轮吸入方式:单吸式 |
| 流量:30m3/h | 叶轮数目:10 | 汽蚀余量:20m |
| 吸入口径:100mm | 排出口径:100mm | 结构原理:中开泵 |
| 级数:多级 | 重量:300kg | 电压:380V |
| 功率:30kw | 规格:DG85-45*9 | 速比:380 |
| 频率:50HZ | 电流:10A | 控制:变频 |
| 电机:工频 | 特性:防腐 | 安装:卧式 |
【***部分:产品概述与核心特性 / Part 1: Product Overview & Core Features】
中文描述
***锅炉给水解决方案DG85-45*9是上海凯泉专为中高压锅炉给水工况研发的高性能多级离心泵。该系列产品结合了***的水力设计与精密的制造工艺,旨在提供高效、稳定且持久的运行表现,是电厂、工业锅炉及区域供热系统的理想选择。
核心优势:
高效节能: 采用***的 CFD 流场分析技术优化叶轮与导叶设计,***提升水力效率,降低运行能耗。
耐高温高压: 专为苛刻工况设计,CR27 特殊材质具备优异的耐磨损和耐腐蚀性能,确保在高温高压下长期稳定运行。
精密制造: 核心部件采用精密铸造工艺,***了部件的尺寸精度和流道光洁度,进一步减少水力损失。
可靠密封: 标配原厂高性能 M3N-55 机械密封,有效防止泄漏,减少维护频次,确保机房环境整洁。
运行平稳: 转子部件经过严格的动平衡校验,结构紧凑,振动小,噪音低。
English Description
Professional Boiler Feed SolutionThe DG85-45*9 is a high-performance multistage centrifugal pump engineered by Shanghai Kaiquan specifically for medium-to-high pressure boiler feed applications. Combining advanced hydraulic design with precision manufacturing, this series delivers efficient, stable, and durable operation, making it ideal for power plants, industrial boilers, and district heating systems.
Core Features:
High Efficiency & Energy Saving: Utilizing advanced CFD flow analysis to optimize impeller and diffuser design, significantly improving hydraulic efficiency and reducing operating costs.
High Temperature & Pressure Resistance: Designed for demanding conditions, the special 304 material offers excellent wear and corrosion resistance, ensuring long-term stability under high temperature and pressure.
Precision Manufacturing: Core components are manufactured using precision casting processes, ensuring dimensional accuracy and smooth flow passages to further minimize hydraulic losses.
Reliable Sealing: Equipped standard with high-performance genuine M3N-55 mechanical seals to effectively prevent leakage, reduce maintenance frequency, and keep the pump room clean.
Smooth Operation: Rotor components undergo strict dynamic balance testing. The compact structure results in low vibration and low noise.
【***部分:基本技术参数 / Part 2: Basic Technical Parameters】
(注:具体参数以实际铭牌和技术协议为准 / Note: Specific parameters are subject to the actual nameplate and technical agreement.)
【第三部分:安装指南 / Part 3: Installation Guide】
中文安装注意事项
基础准备: 泵组应安装在平整、坚固的混凝土基础上,并使用地脚螺栓固定,以防止运行时产生振动。
对中调整: 安装时必须严格校正泵轴与电机轴的同轴度。错误的对中会导致振动加剧、轴承和机封过早损坏。
管路支撑: 进出口管路必须设有独立的支架支撑,严禁将管路重量直接施加在泵体上,以免造成泵体变形。
进口过滤: 建议在泵进口管路上安装目数合适的过滤器,防止杂质进入泵内损坏叶轮和密封环。
排气引水: ***启动前,必须打开泵体上的排气阀进行灌泵引水,排净泵内空气,严禁无水空转。
English Installation Notes
Foundation Preparation: The pump unit should be installed on a flat, solid concrete foundation and secured with anchor bolts to prevent vibration during operation.
Alignment Adjustment: The concentricity of the pump shaft and motor shaft must be strictly calibrated during installation. Incorrect alignment will lead to increased vibration and premature failure of bearings and mechanical seals.
Piping Support: Inlet and outlet pipelines must have independent supports. It is strictly prohibited to impose the weight of the piping directly onto the pump casing to avoid deformation.
Inlet Filtration: It is recommended to install a filter with an appropriate mesh size on the pump inlet line to prevent debris from entering the pump and damaging impellers and wear rings.
Priming & Venting: Before the initial start-up, open the air vent valve on the pump casing to prime the pump with water and exhaust all air. Dry running is strictly prohibited.
【第四部分:维修保养注意事项 / Part 4: Maintenance & Repair Notes】
中文维保注意事项
日常巡检: 定期检查泵的运行电流、出口压力、振动和噪音情况。注意观察机械密封是否有泄漏,允许有微量滴漏,但若泄漏过大需及时更换。
轴承润滑: 定期检查轴承润滑油位(或润滑脂),并按规定周期补充或更换符合要求的润滑剂,***轴承良好润滑。
定期检查: 建议每运行 3-6 个月对泵进行一次小修检查,检查联轴器对中情况、清理过滤器、紧固松动的螺栓等。
冬季防护: 在寒冷环境下,若泵长期停用,必须排尽泵体内和管路中的积水,以防结冰冻裂泵体。
配件更换: 更换叶轮、口环、机械密封等关键零部件时,务必选用原厂配件,以确保泵的性能和可靠性。
English Maintenance Notes
Daily Inspection: Regularly check the pump's operating current, discharge pressure, vibration, and noise level. Observe the mechanical seal for leakage; minor dripping is acceptable, but excessive leakage requires prompt replacement.
Bearing Lubrication: Regularly check the bearing oil level (or grease) and replenish or replace the lubricant with the specified type according to the maintenance schedule to ensure proper lubrication.
Regular Check-up: It is recommended to perform a minor inspection every 3-6 months of operation, including checking coupling alignment, cleaning filters, and tightening loose bolts.
Winter Protection: In cold environments, if the pump is out of service for a long period, all water in the pump casing and piping must be drained to prevent freezing and cracking the casing.
Spare Parts Replacement: When replacing critical components such as impellers, wear rings, or mechanical seals, always use genuine original spare parts to ensure the pump's performance and reliability.
凯泉集团是集设计、生产、销售泵、给水设备及泵用控制设备于一体的大型综合性泵业公司,是中国泵行业的***企业。总资产达25亿元,在上海、浙江、河北、辽宁、安徽等省市拥有7家企业,5个工业园区,总占地面积近1000亩,生产性建筑面积35万平方米。凯泉集团获得了“上海市质量金奖”、“上海市私营企业***第四名”、“上海市科技***企业”、 “上海市产品”、“上海市***商标”、“***”、“中国质量信用***”、“全国合同信用等级***”、“质量、信誉、服务三优企业”、 “中国竞争力的商品商标”、“全国企业文化建设***单位”等光荣称号,2011年凯泉入选全国机械***,名列泵***。 高端人才和高素质的员工队伍是凯泉发展的动力。集团现有员工5000多人,80%员工具有大专以上学历,其中工程技术人员750多名,主要由***水泵专家教授、博士硕士、中***工程师构成,形成了具有创新思维的梯队人才结构。 科技创新,是凯泉基业长青的生命之源。集团是上海市高新技术企业、上海市知识产权示范企业和上海市***示范企业。上海市级的“企业技术中心”,每年以销售总额的5%,用于技术创新和新产品研发。引进了世界***的CFD流体力学专业内流场分析、CAE有限元理论计算及CIMATRON三维CAD、CAM、CAE、FMS等研究设计软件系统。并与上海交大、江苏大学等近10所高等院校和研究所建立了长期的战略合作关系,形成了以自主知识产权为核心的技术体系。拥有***近二百项(其中国家发明***5项),全国建设行业科技成果推广项目2项,国家科学技术进步二等奖一项。
点击查看>| 企业类型 | 有限责任公司(自然人投资或控股) | 注册资本 | 30000.00万人民币 |
| 公司注册地址 | 上海市嘉定区曹安公路4255号、4287号 | 统一社会信用代码 | 91310000630452482T |
| 登记机关 | 嘉定区市场监督管理局 | 法定代表人 | 林凯文 |
| 公司成立日期 | 1996-07-16 | 营业期限 | 1996-07-16 至 2073-07-15 |
| 经营范围 | 一般项目:泵、给水设备及其电控设备,机电产品制造加工、销售,一体化污水处理设备、一体化智能泵房、一体化泵闸系统及附属设备、雨水收集设备、城市排水设施管理,智能水务系统开发,计算机系统集成,软件开发,机械设备维修,从事机械设备科技领域内技术开发、技术转让、技术咨询、技术服务,自有房屋租赁。(除依法须经批准的项目外,凭营业执照依法自主开展经营活动) 许可项目:货物进出口;技术进出口;各类工程建设活动。(依法须经批准的项目,经相关部门批准后方可开展经营活动,具体经营项目以相关部门批准文件或许可证件为准) | ||





