您好,欢迎来到推发网 最新产品

价    格

订货量

  • ¥145.00

    ≥2只

章先生总经理
  • 邮箱已验证
  • 手机已验证
  • 微信已验证
𐁅𐁆𐁇 𐁈𐁇𐁉𐁊 𐁅𐁋𐁋𐁋 𐁋𐁆𐁉𐁉𐁌𐁈𐁅𐁉𐁊𐁋𐁍𐁈𐁎
  • 发货地浙江 乐清市
  • 发货期限2天内发货
  • 供货总量350只
产品推荐
产品特性:隔离型是否进口:否产地:温州
开关类型:PC级品牌:上海人民电气型号:RMQ4-系列
绝缘电压:690V额定电压:400V额定电流:63A~2000A
极数:4P产品认证:CCC额定冲击耐受电压:8kV
额定短路接通能力:10kA额定短时耐受电流:15kA机械寿命:2000
电气寿命:1000最小包装数:13C额定电压范围:1500V以下
系列:RMQ4-系列
双电源自动转换开关RMQ4-4P 100A160A200A250A400A630A

RMQ4 双电源自动转换开关(ATS)简介



一、产品是什么

RMQ4 属于自动转换开关电器(ATS),用于两路电源(市电 — 市电、市电 — 发电机)之间的自动 / 手动切换:常用电源失电、欠压、超压或断相时自动投入备用电源,常用电源恢复后自动返回。执行元件为负荷开关或断路器,配智能控制器,符合 GB/T 14048.11 / IEC 60947-6-1,使用类别多为 AC-33iB / AC-33B。

二、型号怎么读

RMQ4 - □ / □  □

表格

段含义
RMQ4自动转换开关,设计代号 4;后续字母多表示级别 / 结构(如 D 智能型、F 消防型、P 末端型)
***段数字壳架 / 额定工作电流,常见档位 125、250、400、630、1000、1600、2000、3200A
斜杠后***位极数:3P(三相)或 4P(三相 + 中性线,常用于带 N 线的配电)
末位级别 / 控制类型:PC 级(负荷开关本体)、CB 级(断路器本体);控制上分末端型、智能型、消防型

三、关键参数(通用口径,具体以你们厂样本铭牌为准)

表格

项目典型值
额定工作电压 UeAC 400V(部分至 690V)
额定绝缘电压 Ui660—800V
额定冲击耐受 Uimp8—12kV(主电路)
额定电流16A—3200A 多档
极数3P / 4P
转换方式电机驱动,先断后合
转换时间常规 ≤3s;快速型 0.5—1.5s(末端照明 / IT 负载要选快切)
机械寿命5,000—6,000 次
电气寿命1,000—1,500 次(AC-33iB)
短路能力PC 级本体不分断短路电流,须由前级 MCCB 保护;CB 级自带短路 / 过载保护
使用环境-5℃—+40℃(部分 -25℃—+55℃),海拔 ≤2000m

四、控制器核心功能(选型看这几项就够)

  1. 自投自复 / 自投不自复 / 互为备用 三种工作模式;

  2. 电压整定:过压、欠压、断相阈值可设(常见过压 270V、欠压 170V,回差 3s);

  3. 转换延时与返回延时(0—255s),避免市电瞬时波动来回切换;

  4. 双分位置(O 位):两路同时断开,检修时安全隔离;

  5. 消防联动:DC24V 信号输入,火警时强制切到双分并输出无源反馈触点(501/502 输入、503/504 反馈);

  6. 发电机控制:输出启停干接点,市电失电先启动机组、电压建立后再转换;

  7. 通讯 / 远程:RS485(Modbus)上传状态,可接入 BA / 动环系统。

五、落地选型要点

  • PC 级还是 CB 级:消防泵、消防风机、电梯等不允许保护跳闸的负载,选 PC 级(只切换不保护,前级另设保护);普通照明、动力末端可用 CB 级(自带保护更省柜内空间)。

  • 极数:有中性线且需要同时切换的(如带漏电保护、单相负载多的回路)用 4P;纯三相动力可用 3P,但要确认 N 线处理方式。

  • 电流:按负载计算电流的 1.1—1.25 倍选,注意 ATS 是短时工作制设备,不要当长期满载开关用。

  • 消防 / 发电机场景:必须选带消防联动端子和发电机启停输出的智能型 / 消防型控制器,否则验收过不了。

  • 上下级配合:PC 级 ATS 前级 MCCB 的 Icu 要覆盖预期短路电流;CB 级 ATS 的 Ics 要与前级选择性配合,避免越级跳闸。

六、常见误区

  • 把 ATS 当隔离开关长期带电操作 → 触点磨损快,电气寿命只有 1,000—1,500 次;

  • 使用 3P ATS 却把 N 线直接短接两路 → 备用电源投入时形成环流;

  • 未设置返回延时 → 市电闪断时频繁切换,电机类负载容易跳闸。



RMQ4 Series Automatic Transfer Switch (ATS)

DescriptionThe RMQ4 series is a motor-operated automatic transfer switch designed for two-source supply systems — utility-to-utility or utility-to-generator. When the normal source fails, drops below the set undervoltage threshold, rises above the overvoltage threshold or loses a phase, the controller starts the transfer sequence and connects the load to the standby source; when the normal source recovers and stabilizes, the load is transferred back automatically. Open-transition (break-before-make) design with a true centre-off (double-open) position for safe ***lation during maintenance. Available in PC class (load-switch body, no short-circuit breaking) and CB class (circuit-breaker body with integrated protection). Conforms to GB/T 14048.11 and IEC 60947-6-1, utilization category AC-33iB / AC-33B.

Model designationRMQ4 – [rated current] / [poles] [class] ? Rated current: 16A to 3200A (typical frames 125 / 250 / 400 / 630 / 1000 / 1600 / 2000 / 3200A) ? Poles: 3P or 4P (4P switches the neutral together with the three phases) ? Class and control type: PC class (load switch) or CB class (circuit breaker); terminal type, intelligent type or fire-service type controller

Key technical data

表格

ItemTypical value
Rated operational voltage (Ue)AC 400V (up to 690V on request)
Rated insulation voltage (Ui)660–800V
Rated impulse withstand (Uimp)8–12kV (main circuit)
Rated current16–3200A
Poles3P / 4P
Transfer modeMotor driven, break-before-make, with centre-off position
Transfer time≤3s standard; 0.5–1.5s for fast-transfer versions
Mechanical endurance5,000–6,000 operations
Electrical endurance1,000–1,500 operations (AC-33iB)
Short-circuit capabilityPC class: no breaking capacity — upstream MCCB required; CB class: integrated short-circuit and overload protection
Operating temperature-5 °C to +40 °C (optional -25 °C to +55 °C)
Altitude≤2,000 m
StandardsGB/T 14048.11, IEC 60947-6-1

Controller functions? Three operating modes: auto-transfer with auto-return, auto-transfer without return, and mutual standby ? Adjustable overvoltage / undervoltage / phase-loss thresholds with adjustable return hysteresis (typically 3 s) ? Adjustable transfer delay and return delay (0–255 s) to ride through utility transients ? True double-open (centre-off) position for maintenance ***lation ? Fire-service linkage: DC24V signal input forces the switch to the double-open position and provides volt-free confirmation contacts ? Generator control: volt-free start/stop contacts — generator is started and its voltage verified before transfer ? Remote monitoring via RS485 (Modbus) for BMS / building automation integration ? Manual operation by handle when control power is unavailable

Features? PC and CB class options to suit both fire-service loads (no protective tripping allowed) and general distribution loads ? Fast-transfer versions for lighting, UPS and IT loads sensitive to interruption ? Clear mechanical position indicator: I (normal) – O (double open) – II (standby) ? Modular controller, front-accessible settings, no PC required for commissioning ? Wide current range up to 3200A for main incoming and sub-main applications

Typical applicationsFire pump and fire-fan supply circuits, elevator and life-safety loads, hospitals, data rooms, high-rise buildings, factories and commercial complexes where two independent sources or a standby generator must be switched automatically.

Ordering informationPlease specify: ① rated current and frame; ② number of poles (3P / 4P); ③ class (PC or CB); ④ controller type (terminal / intelligent / fire-service); ⑤ required transfer time (standard ≤3s or fast 0.5–1.5s); ⑥ whether generator-start output and RS485 communication are required; ⑦ cable entry and mounting arrangement.

ManufacturerZhejiang Jiudian Electric Co., Ltd. — marketed under Shanghai People's Electric (HK).


供应商信息
公司图片
浙江九电电气有限公司 进入首页

浙江九电电气有限公司于中国电器之都之称的温州市乐清市柳市镇,本企业建于2010年,具有一批***设备和一支具有创新精神的研发团队。   公司是专业生产配电输电设备的生产企业,主要生产塑壳断路器,智能型框架断路器,交流接触器,空气开关,透明断路器,无功功率补偿器,复合开关,容性无触点开关,直流接触器,切换电容接触器,刀开关,电能表等系列低压成套元器件产品,本公司集开发,生产,销售服务为一体的现代化企业。   本公司奉行“以市场为中心,以创新为主导,以质量为基础,以信誉为生命”的企业宗旨,立足本行,不断使企业向多元化、规模化、集团化推进。   面对全球经济的挑战,公司全体员工正满怀信心,积极***,正全面推进“人才造就工程,形象塑造工程,质量升级工程,科技改善工程和市场拓展工程”等五大基础工程,为把本公司做大做强打下坚实的基础。   公司经营近年来,承蒙国内外新老顾客的长期支持和友好合作,产品***各地,并出口东南亚,俄罗斯,中东以及南非等国家和地区,面对全球一体化的今天,我们以***的服务,***的产品质量和优惠的价格与国内外厂商携手合作,工展鸿图,实现共赢!   公司文化:本公司以人为本,信誉至上,质量,正在沿着改革开放道路快速稳步的向前发展。   公司今后的发展方向:面对经济的挑战,本公司全面推进以“战略人才资源管理”为重点,从劳动密集型产业向科技密集型产业转移,从商品经营向商品和资本并举转移,从国内市场向扩大国际市场并重转移的发展策略。 实现九电在未来更高方向的宏伟蓝图而努力奋斗!!! 官方地址:

点击查看>
企业类型 私营有限责任公司 注册资本 50.00万人民币
公司注册地址 浙江省乐清市柳市镇黄七甲村 统一社会信用代码 91330382586254154T
登记机关 乐清市工商行政管理局 法定代表人 章新奉
公司成立日期 2011-11-08 营业期限 2021-11-07
经营范围 配电开关控制设备,电力电子元器件,其他输配电及控制设备,高低压电器及配件制造,加工、销售。
联系方式
联系人
章先生微信
𐁅𐁆𐁇 𐁈𐁇𐁉𐁊 𐁅𐁋𐁋𐁋
浙江九电电气有限公司
  • 电       话 𐁋𐁆𐁉𐁉𐁌𐁈𐁅𐁉𐁊𐁋𐁍𐁈𐁎
  • 传       真 𐁋𐁆𐁉𐁉𐁌𐁈𐁊𐁉𐁅𐁉𐁍𐁈𐁎
  • 地       址 浙江 温州 乐清市 乐清市柳市镇黄七甲工业区
  • 免责声明 :

    本页面所展现的双电源自动转换开关RMQ4-4P 100A160A200A250A400A630A信息及其他相关推荐信息,均来源于其对应的商铺,信息的真实性、准确性和合法性由该信息的来源商铺所属企业完全负责。推发网对此不承担任何保证责任。

  • 友情提醒 :

    建议您在购买相关产品前务必确认供应商资质及产品质量,过低的价格有可能是虚假信息,请谨慎对待,谨防欺诈行为。

浙江九电电气有限公司
  • 身份验证
    • 营业执照已上传
    • 邮箱已验证
    • 手机已验证
    • 微信已验证
  • 经营模式
    生产加工
  • 注册资本
    50.00万人民币
  • 企业类型
    私营有限责任公司
  • 主营产品
  • 公司地址
    浙江 温州 乐清市 乐清市柳市镇黄七甲工业区
在线留言
本页信息为浙江九电电气有限公司为您提供的"双电源自动转换开关RMQ4-4P 100A160A200A250A400A630A"产品信息,如您想了解更多关于"双电源自动转换开关RMQ4-4P 100A160A200A250A400A630A"价格、型号、厂家请联系厂家,或给厂家留言。 进入店铺 在线留言