| 品牌:远东 | 型号:2CY-0.6齿轮泵 | 材质:铸铁 |
| 流量:0.6m3/h | 转速:1450 |
用途:
2CY齿轮泵适用于输送不含固体颗粒和纤维,无腐蚀性,温度不高于200℃,粘度为5×10-6~.5×10-3m2/s(5-1500cSt)的润滑油或性质类似润滑油的其他液体以及用于液压转动系统. 2 cy gear pump is suitable for conveying containing no solidparticles and fibers, non-corrosive, temperature is not higher than 200 ℃, the viscosity of 5 x 10-6 ~. 5 x 10-3 m2 / s (5 to 1500 CST) thenature of the lubricating oil or other similar oil liquid and used forhydraulic rotation system.
工作原理
2CY齿轮油泵系容积式泵,主,被动齿轮与泵体,左右泵盖组成进油,出油二个封闭空间,当齿轮转动时,进油腔的容积,由于啮合齿不断脱开,而由小变大.形成真空,将液体吸入,有齿谷带往油腔,而出油腔容积,由于啮合齿的不断进入啮合而大变小,油液受压缩而被排出,从而达到输送油料的目的. 2 cy gear oil pump is a positive displacement pump, the main,driven gear and the pump body, pump cover around of feed, oil two closed space,when the gears, the oil cavity, the volume of meshing teeth off constantly, andchange from small to large. The formation of a vacuum, the liquid suction,toothed valley to the oil cavity, and the volume of the oil cavity, due to theconstant into the mesh of the meshing teeth and large to small, oil isdisplaced by compression, so as to achieve the aim of oil.
结构特点
本系列齿轮泵主要有齿轮,轴,泵体,泵盖,轴承套,轴端密封等组成.齿轮经氮化处理有较高的硬度和耐磨性.与轴一同安装在可更换的轴套内运转.泵内全部零件的润滑均在泵工作时利用输送介质而自动达到.泵内四个轴承套在泵内浮动安装,随工作压力大小自动调整端面间隙,因此泵的压力稳定,输出流量脉动小,溶积效***.从主轴外伸端向泵看,为顺时针旋转. This series gear pump are mainlygear, shaft, pump body, pump cover, bearings, shaft end seal, etc. The gearafter nitriding treatment had a higher hardness and wear resistance. With theshaft installed in the replaceable shaft sleeve. In all parts of thelubrication pump are using the transmission medium and automatic for when thepump work. Four bearing sleeve inside the pump in the pump float installation,along with the work pressure automatically adjusts end clearance, so the pumppressure stability, the output flow pulsation is small, high volume efficiency.From the main shaft overhang end to the pump, for clockwise.
应用范围
在输油系统中可用作传输,增压泵; In the oilsystem can be used as a transport, booster pump;
在燃油系统中可用作输送,加压,喷射的燃油泵; In the fuel system can be used as a transport, pressure, jet fuel pump;
在液压传动系统中可用作提供液压动力的液压泵; In the hydraulic drive system canbe used as a hydraulic pump of hydraulic power;
在一切工业领域中,均可作润滑油泵用;In allindustrial areas, can be used as lubricating oil pump;
使用与安装: Use and installation:
1、机组应安装在水平水泥基础上,用地脚螺栓固定。1, theunit should be installed in a horizontal cement, on the basis of land use fixedbolt.
2、右联轴器应同轴,安装完成后,转动联轴器确认运转顺畅无负压力现象后,方可进入运行。2, should right coupling coaxial, after the installation iscomplete, turn the coupling confirmed after running smoothly without negativepressure phenomenon, may run into.
3、泵不适合输送不洁油液,故在进口管端应设滤油器。3, thepump is not suitable for conveying impurity oil, therefore, at the inlet pipeshould be set oil filter.
4、泵无安全阀,建议在排油管路中,设安全阀,以确保系统安全运行。4no relief valve, pump, it is suggested that in the discharge of oil pipeline, asafety valve, and to ensure the safe operation of the system.
5、泵的安装高度,不超过允许吸上高度。5, pumpinstallation height, no more than allow on the suction height.
6、泵的转向规定:从泵端向电机看,旋转方向为逆时针。6,pump steering regulation: look from the pump to the motor, for counterclockwiserotation direction.
工作注意事项: Work matters needing attention:
1、开机前应检查泵轴转动是否灵活,有无卡阻现象,进出口管道上的阀门是否开启,泵的旋转方向是否正确。1, should check whether the pump shaft rotation is flexible, beforestarting the presence of jam phenomenon, import and export pipeline valve ***pen, the direction of rotation of the pump is correct.
2、长时间没有使用的泵开机前应向泵腔中注入一定量的润滑液,以减少泵在吸油过程中的干摩擦,并可提高泵自吸性能。2, long time no use the pump to the pump before starting the cavityinject a certain amount of lubricant to reduce the pump in the dry friction inthe process of oil absorption, and can improve the performance of pump.
3、开机后如有不正常的噪音或过热现象,应立即停车检查。3,after the boot if there is any abnormal noise or overheating phenomenon, shouldimmediately stop check.
4、检查泵轴端有无泄露现象,如:对填料密封应适当调紧压紧盖、其他密封则应拆机检查。4, check whether there is any leakage on the pump shaft endphenomenon, such as: the packing should be properly tighten clamp cover andother sealing should teardown check.5、若输送热油,在开车时应均匀预热,预热是利用被输送的介质不断通过泵体进行的。5, if conveying hot oil, while driving should be uniform preheating,preheating is to use the media constantly through the pump body to bedelivered.
6、泵停机时,首先切断电源,然后关闭进出口管道上的阀门,避免造成泵倒转。6,when the pump stop, cut off power supply first, then close the import andexport pipeline valve, avoid to cause back pump.
使用与安装:1、机组应安装在水平水泥基础上,用地脚螺栓固定。2、右联轴器应同轴,安装完成后,转动联轴器确认运转顺畅无负压力现象后,方可进入运行。3、泵不适合输送不洁油液,故在进口管端应设滤油器。4、泵无安全阀,建议在排油管路中,设安全阀,以确保系统安全运行。5、泵的安装高度,不超过允许吸上高度。6、泵的转向规定:从泵端向电机看,旋转方向为逆时针。Use andinstallation: 1, the unit should be installed in a horizontal cement, on thebasis of land use fixed bolt.2, should right coupling coaxial, after theinstallation is complete, turn the coupling confirmed after running smoothlywithout negative pressure phenomenon, may run into.3, the pump is not suitablefor conveying impurity oil, therefore, at the inlet pipe should be set oilfilter.4 no relief valve, pump, it is suggested that in the discharge of oilpipeline, a safety valve, and to ensure the safe operation of the system.5,pump installation height, no more than allow on the suction height.6, pumpsteering regulation: look from the pump to the motor, for counterclockwiserotation direction.
工作原理:本泵系容积式泵,主、被动齿轮与泵体、左右泵盖组成进油、出油二个封闭空间,当齿轮转动时,进油腔的容积,由于啮合齿不断脱开,而由小变大。形成真空,将液体吸入,有齿谷带往油腔,而出油腔容积,由于啮合齿的不断进入啮合而大变小,油液受压缩而被排出,从而达到输送油料的目的。Working principle: this pump is a positive displacement pump, themain around, passive gear and pump body, pump cover of the oil, the oil twoclosed space, when the gears, the oil cavity, the volume of meshing teeth offconstantly, and changes from small to big.Form a vacuum, the liquid suction,toothed valley to the oil cavity, the volume of the oil cavity, due to theconstant into the mesh of the meshing teeth and large to small, oil isdisplaced by compression, so as to achieve the aim of oil.
用途:2CY齿轮泵主要用于各种机械设备中的润滑系统中输送润滑油。Purpose: 2 cy gear pump is mainly used for all kinds of mechanicalequipment of conveying lubricating oil lubrication system.
工作原理:本泵系容积式泵,主、被动齿轮与泵体、左右泵盖组成进油、出油二个封闭空间,当齿轮转动时,进油腔的容积,由于啮合齿不断脱开,而由小变大。形成真空,将液体吸入,有齿谷带往油腔,而出油腔容积,由于啮合齿的不断进入啮合而大变小,油液受压缩而被排出,从而达到输送油料的目的。Working principle: this pump is a positive displacement pump, themain around, passive gear and pump body, pump cover of the oil, the oil twoclosed space, when the gears, the oil cavity, the volume of meshing teeth offconstantly, and changes from small to big.Form a vacuum, the liquid suction,toothed valley to the oil cavity, the volume of the oil cavity, due to the constantinto the mesh of the meshing teeth and large to small, oil is displaced bycompression, so as to achieve the aim of oil.
结构说明:本系列泵主要由:左、右泵盖、泵体、主、被动齿轮轴、轴套、油封等零件组成。Structure description: this series of pump is mainly composed of:left, right, pump cover, pump body, master, passive gear shaft, shaft sleeve,oil seal and other parts.
| 轻柴油供油泵 | NYP-320B-LR-M1-J-W51高粘度泵 | 山东新龙集团有限公司 |
| 润滑油排油泵 | NYP220B-RL-T2-A/J-W21高粘度 | 荣成市泓运船业有限公司 |
| 润滑油输送泵 | NYP50-RU-T2-W51高粘度泵 | 湖北华舟有限公司 |
| 胶水专用齿轮泵 | NYP-320B-RL-T2-A/J-W21高粘度泵 | 青海盐湖工业股份有限公司 |
| 抽沥青泵 | NYP220B-RL-T2-A/J-W21高粘度泵 | 江苏中达新材料集团股份有限公司 |
| 水溶性高分子胶体泵 | NYP220B-RL-T2-A/J-W21高粘度泵 | 山东金正大生态工程股份有限公司 |
| 液体硫磺泵 | G20-1P-W101单螺杆泵 | 山东海科化工集团有限公司 |
| PU合成革聚氨酯树脂泵 | NYP-24高粘度泵 | 浙江昱辉阳光能源有限公司 |
| 输送灌封胶泵 | NYP110-RU-T2-W11高粘度泵 | 贵州开磷(集团)有限责任公司 |
| 输送封口胶泵 | NYP-320高粘度泵 | 贵州轮胎股份有限公司 |
| 消防泡沫灭火剂泵 | G40-2V-W102单螺杆泵 | 山东胜通集团股份有限公司 |
| 输送泡沫原液泵 | W6.4ZK90Z1M1W73双螺杆泵 | 上海申达股份有限公司 |
| 油库装卸泵 | W3.1ZK-30Z1M1W73双螺杆泵 | 山东海力化工股份有限公司 |
| 胶乳泵 | NYP-320B-RU-T1-W12高粘度泵 | 山西兰花科技创业股份有限公司 |
| 船用柴油机喷油泵 | SMH440R43E6.7W28三螺杆泵 | 四川空分设备(集团)有限责任公司 |
| 拉环油齿轮泵 | KCB55齿轮泵 | 山东三工橡胶有限公司 |
| 沥青混合料专用泵 | NYP-80高粘度泵 | 福建金纶高纤股份有限公司 |
| 高粘度耐酸泵 | NYP50-RU-T2-W51高粘度泵 | 广东嘉宝莉化工有限公司 |
| 沥青加压输送泵 | NYP24-RL-T2-A-W61高粘度泵 | 徐州徐轮橡胶有限公司 |
| 高粘度乳液泵 | NYP110高粘度泵 | 山西天泽煤化工集团股份公司 |
| 输送色氨酸泵 | G25-1V-W102单螺杆泵 | 成都市新都化工股份有限公司 |
| 输送苏氨酸泵 | G40-1V-W101单螺杆泵 | 江苏梅兰化工集团有限公司 |
| 主机滑油泵 | SMH1700R42U12.1W28三螺杆泵 | 枣庄扬帆船舶有限公司 |
河北远东泵业制造有限公司坐落于铸造名乡—河北省泊头市。公司占地面积38650平方米,建筑面积20300平方米,是国内***的集设计、铸造、生产、销售、服务于一体的容积泵专业制造厂家。公司始建于1984年,有二十几年专业研制经验。目前产品设计采用国际***水平实体设计软件;产品研发、制造、检验、交付按照***质量管理体系控制过程质量;产品制造广泛使用加工中心、数控机床、专用精机、高精设备;检测设备拥有万能工具显微镜、渐开线检测仪、光学投影仪、万能测齿仪、脉冲辉光离子氮化炉等大型检测设备,并建有国家B级试验站。本厂以***的产品水平、优质的售后服务、恪守信用而在市场上倍受欢迎,产品***不衰,赢得了用户的普遍赞誉。公司已通过***:2000国际质量体系认证,中国船级社CCS型式认证,法国船级社BV产品工厂认证,美国船级社ABS产品质量认证,中国渔业船舶检验局船用泵认证,成为中石油物资资源市场成员、中石化物资资源市场成员。河北省知名产品生产企业,船用泵产品承制企业。
点击查看>| 企业类型 | 有限责任公司 | 注册资本 | 2000万人民币 |
| 公司注册地址 | 河北省泊头市道东街88号 | 统一社会信用代码 | 130981000004590 |
| 登记机关 | 泊头市工商管理所 | 法定代表人 | 蔡文福 |
| 公司成立日期 | 2003-09-19 | 营业期限 | 30 |
| 经营范围 | 生产和销售各种泵 铸件加工 | ||



